Custom Made Chambers

Custom Made Chambers

Translate

Friday, September 21, 2018

ARTICLE: Peyronies Disease-Curvature of the Penis, what is normal?



-->CLICK HERE FOR LG HANGER SYSTEM<--

A man's erection can point in virtually any direction. Straight ahead, left or right, up or down, there's no right or wrong.




There is no such thing as a unique angle.

The following data come from a study that measured the erections of 1,565 men.

In the figure to the right, if the penis pointed directly up, it was measured as 0 degrees, and if it was forward-pointing (horizontal), it would be 90 degrees:

  • 0–30 degrees — 4.9 percent of men
  • 30–60 degrees — 29.6 percent of men
  • 60–85 degrees — 30.9 percent of men
  • 85–95 degrees — 9.9 percent of men
  • 95–120 degrees — 19.8 percent of men
  • 120–180 degrees — 4.9 percent of men

If you've ever been concerned that your chap is a bit skew-whiff, don't worry — you're normal. While we're on the topic of "normality," very few penises are straight. They can curve in any direction. A curve of up to 30 degrees is still considered normal.

Monday, September 17, 2018

Your Chamber is NOT too big

Your chamber is not too big. I always manufacture chambers with room for growth. And as long as the measurements you provided us were accurate your chamber is not the issue. Trouble shooting the problem you're having has a two-fold answer.

#1 - Your sleeve may be too tight, to test to see if that's the issue, wear a two inch portion of your sleeve at the base of your penis for an hour without the chamber. If your penis gets cold, then the sleeve is too tight and you can either stretch your sleeve up over a larger object for 24 hours to stretch it bigger, or you can purchase a larger 1" sleeve.

#2 - You could be using too much vacuum pressure. If you're using any more than 10 Hg's then that's too much. In fact with as little weight as you are using you should be able to use a little as 5 Hg's of pressure. Furthermore it's fine that a little bit of the sleeve gets sucked forward into the mouth of the chamber. That's actually a good indicator that your sleeve and penis skin have a good vacuum seal.

The fact that you took two months off doesn't help with the issues you're experiencing. During the layoff you lost all the tissue conditioning you had achieved. During the conditioning process (which can take several weeks) your penis will start to respond to the traction by expanding during the hang session. Ideally over the course of about 3 months you should start to experience expansion to the point where your penis packs the chamber completely. This doesn't happen in a couple weeks. It's a transitional experience that takes place with consistent, dedicated training.

I believe if you do a sufficient warm up - take a warm or hot shower prior to your hang session, do some moderate jelqs to loosen your flaccid penis and pull some blood into it so that you are at your fullest flaccid state... even slightly erect at about 30-50% this will help your penis circulation. Once you install your chamber you can help the expansion and circulation by priming your chamber 6-8 times. You do this by drawing out 10 - 15 Hg's of pressure, holding it for 5 seconds and releasing the pressure. Repeat this 6-8 times and then on the last prime go up to 10 Hg's and allow your penis some time to expand before you hook up any weight. About 5 minutes should be enough. Then release the pressure, and go up to 5 Hg's of fresh vacuum pressure, disconnect the hose and attach your 3 lbs of weight and do your hang session. Remember to do your 5-10 minutes of aggressive hand stretches / jelqs immediately after your hang session in order to take full advantage of the fatigue you have induced from the hang. Wear a Girth Band at the base of your penis to prevent retraction and keep your flaccid penis full and long.

Monday, September 10, 2018

ARTICLE: Amount of Hg's to use per amount of weight




How many Hg's should I be using per amount of weight?

This is somewhat subjective. It also depends on how much weight you are attempting to hang. For example when I am hanging 8 lbs., I draw out about 3 hg of vacuum pressure and hook the weight up to the chamber, lower it until it is hanging onto my penis all by itself. I take a look at the gauge and it will read about 5 hg, The weight alone primed the pressure up another 2 hg. That is sufficient for me to hang 8 lbs. When I go up to 10 lbs and above, I do the same, except as I allow the weight to hang I draw the desired pressure I need to allow the weight to hang without slipping off, which is about 10 hg. So draw up to 5 hg, allow the weight to hang, it will spike up a couple more hg, and then draw out the remainder up to 10 hg and disconnect hose. Even when I hang up to 17 lbs. I never need more than about 15 hg. of pressure.